I got it bought since July 5. @tgalati4 .. asked 2 years ago viewed 23812 times active 1 year ago Related 1What to do if my hard disk has bad sectors?9Mark bad sectors on hard drive without formating2end_request i/o error, share|improve this answer answered Jan 29 '14 at 12:29 ewwhite 151k47296576 Not the same hard drive. Extended test got aborted at 40% because of errors. navigate to this website
I was watching the /var/log/kern.log, until I found out that whenever this message appear from the log ata1.00: revalidation failed (errno=-5) each of my applications, automatically close, commands from terminal starts here we are.You say it is probably dying. Some data recovery services will replace the drive controllers, arms, bearing, etc. Total time to complete Offline data collection: ( 609) seconds.
If so, what does this mean? ... Okay, it appears that bad sectors are physically ununusable. Here is what I did: Attached USB HDD to 'old' Model B Pi (powered by Pi), then ran fsck without flags which reported clean fs (ext4). Why use a Zener in a regular as opposed to a regular diode?
After I replaced the SMPS, then I came to know that there is problem with hard drive. –sat Jan 29 '14 at 12:39 add a comment| up vote 4 down vote While you are at it, check for errors/ health of your primary HDD. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 078 046 Pre-fail Always Blk_update_request Io Error SCT Data Table supported.
Has Tony Stark ever "gone commando" in the Iron Man suit? End_request I O Error Dev Sector So I boot my laptop from ubuntu 12.10 on USB, and I didn't mount that harddrive (it's /dev/sda1) and I run: sudo badblocks -nvs /dev/sda1 and output is: [3277.882968] end_request: I/O op_state=1 [ 2.060635] Init: Power Port (0) [ 2.065807] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.074242] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.083127] usb This Site Will this give me some answers?
Why was Arcanine with the Legendary Birds in Veridian City in Pokémon Origins? Blk_update_request I/o Error Dev Sda Sector General Purpose Logging supported. Reason: please use code tags for command line input and output Adv Reply July 11th, 2014 #2 Vladlenin5000 View Profile View Forum Posts Private Message Ubuntu addict and loving it if you could point me to the right point of the code writing those "sd 0:0:0:0: [sda]\nResult: hostbyte=0x07 driverbyte=0x00" I could help you with understanding the failure reason perhaps (althought I
Extended self-test routine recommended polling time: ( 111) minutes. http://unix.stackexchange.com/questions/96989/badblocks-and-end-request-i-o-error-in-output What should I do? I/o Error Dev Sda Sector 0 Anything that possibly works with badblocks?Failing that, does the following have a chance?: 1. End_request I/o Error Dev Sda Sector 0 This site is not affiliated with Linus Torvalds or The Open Group in any way.
At the very least, backups of some sort should have been in the plan. useful reference Self-test supported. In Skyrim, is it possible to upgrade a weapon/armor twice? Sense: Unrecovered read error Jan 29 18:59:13 mint kernel: [ 383.246588] sd 5:0:0:0: [sda] CDB: Read(10): 28 00 02 8f ba f0 00 00 08 00 Jan 29 18:59:13 mint kernel: Blk_update_request I/o Error Ubuntu
The ns1066 chipset (used by orico 6518US3) has some compatibility issues so that when I changed the disk dock to orico 6518S3(which uses ASM1153E chipset), there is no disconnection anymore. As a result the drive failed on different blocks or not at all. Very weird. my review here What, no warning when minipage overflows page?
share|improve this answer edited May 25 at 10:00 answered Feb 17 '12 at 12:23 kingmilo 2,4831128 Sorry. Blk_update_request I/o Error Dev Fd0 Sector 0 No Offline surface scan supported. I'm going to attach the dmsg and lsusb outputs.
UNIX is a registered trademark of The Open Group. MeeGeeVee commented Apr 17, 2015 In my case it was 100% power related. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 00 00 a0 Commands leading to the Blk_update_request I/o Error Dev Sector Topics: Active | Unanswered Index »Kernel & Hardware »Harddisk problem: ata1.00: end_request: I/O error, dev sda, sector ...
reading specific ordinary files (for instance ~/.config/dconf/user) resulted in an I/O error. if the live CD cant read/mount the disk then there likely is no simple/quick way to recover data off the disk. Please let me know if I can try some fix. get redirected here Many disk managing programs such as fdisk like to enumerate all available block devices, and definitely fdisk did hit floppy module and these messages started to appear in your dmesg.
Hopefully it's not a bad drive.Please throw me a bone. share|improve this answer edited May 13 at 4:13 answered May 13 at 4:05 siblynx 1,562212 I had to add /etc/modprobe.d/blacklist-floppy.conf to /etc/mkinitcpio.conf and then run mkinitcpio -p linux to How to insert equation numbers with lstlisting? Offline data collection capabilities: (0x7b) SMART execute Offline immediate.
Run sudo dd if=/dev/sda of=/dev/null count=1 skip=201724230 and see if it complains. –psusi Feb 22 '14 at 16:05 This is what I got: [email protected]:~$ sudo dd if=/dev/sda of=/dev/null count=1 http://www.ebay.com/sch/i.html?_from=R40&_nkw=usb3+y-cable Hope this helps your case too. It "wraps" after 49.710 days. Do you want to help us debug the posting issues ? < is the place to report it, thanks !
specialist data recovery tools/services might get some data off the disk but i would caution you that the recovered data is often not in a useful format and takes many further