I've seen and read about too many problems caused by using non-epson ink, especially on the newer models of epson printers that have come out in the last few years. So most of the printer manufactors produce the cheap small ink jet printers, just to get in on all those thousands of printer sales. If you're using the Scan button, make sure Smart Panel and your operating system are set up for scanning using the button. See Envelopes for instructions. useful reference
That black hose is supposed to be attached to another clear hose. I replaced the Magenta ink cartridge with a new Epson Magenta ink cartridge (not a 3rd party cartridge). Try adjusting the brightness with your application software. Generated Mon, 10 Oct 2016 02:31:05 GMT by s_ac15 (squid/3.5.20)
Error message Solution Quality&Paper setting is not acceptable for B&W copy. They have me between a rock & a hard place.Thanks for your help. The EPSON Stylus CX5400 scanning software doesn't work properly. by unknown on Apr 9, 2005 at 9:12pm Add comment Please sign in to comment 0 I just used the CX5200 instructions for my CX5400 and it worked fine.
Only part of the image is scanned. I've retrieved it from the bottom of the printer but now I have three pieces to reconnect. Paper out - - - >Load paper in Paper tray and press the Color copy button. Epson Stylus Cx5400 Not Printing If that doesn't work, scan in Manual mode.
Thanks--Susan Oates Ü Respond to this 0 I am having the same problem of a scanner error on my Epson. Is the black head dead? (of course the warranty just past)Or will I need to follow the advice above and find a missing tube or is there some other tip.Thanks for If the hot water does not work, then you may need to use the actual "Epson Print Head Cleaning Solution", which is designed by epson company to dissolve its inks. directory IT SEEMS TO APPLY TO SEVERAL OF THE NEWER MODELS OF EPSON PRINTERS AND IS THE MOST COMMON PROBLEM REGUARDING BLANK COPIES: AVTECH 3/14/2004 16:39:23 Re: Epson C82 Not Printing.
I was then able to use a pair of needlenose pliers and a pair of tweezers to put these 2 hoses back together again. Epson Stylus Cx5400 Driver Paper out – – – > Load paper in the Paper tray and press the Color copy button. If you see your EPSON Stylus CX5400 in the Windows Control Panel, but you can't scan, uninstall and reinstall its software; see Uninstalling Your Software. You can generally buy a new small printer cheaper than you can have your old one repaired for.
by Anonymous on Apr 28, 2005 at 7:28pm Add comment Please sign in to comment check out the little feed tube under the printer head it falls off when i put http://fixyourownprinter.com/posts/44414 by Anonymous on Apr 30, 2005 at 9:27am Add comment Please sign in to comment 0 The scanner unit is held on by the 2 screws on the back. Epson Stylus Cx5400 Scanner Error We ran out of black ink, put a new cartridge and the printer stopped printing. Epson Stylus Cx5400 Scan Software I checked the purge tube, and its still connected.
Thanks. http://deepfrom.com/epson-stylus/epson-stylus-cx7000f-printer-error.html Press the On button to turn off the EPSON Stylus CX5400. It took @ 1 hour total time to repair the disconnected tube then test the printer. I have the EXACT same problem that Rachel had. Epson Stylus Cx5400 Ink
I'd appreciate input from anyone who can walk me through this process. It seems like as the selling prices started to come down, so did the quality of the printers. Regards, Joe - Anonymous 0 Joe: You're welcome! this page BTW, I was able to clamp the cap assembly to the side with just a large paper clip.
Generated Mon, 10 Oct 2016 02:31:05 GMT by s_ac15 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Epson Stylus Cx5400 Patronen Red seemed to be more yellow. Make sure you carefully follow the steps on your Start Here sheet when you reinstall your software.
After spending a small fortune on new cartridges to find it still didn't work (it is just out of warranty, been 14 months old) I took off the lid (4 screws, Anything else I can try? One individual print head nozzle is so tiny, that it will not accept a human hair. Cartouche Epson Stylus Cx5400 Your printout is blurry or smeared.
When I click the monitor icon the message is that "printer is not ready to print" and "check all connections and make sure all devices are on". I certainly will not be buying any Epson products in future, as I have a slight suspicion this problem is induced by software installed either in the CX5400 or the installation Be sure you also check out the "Dura Brite Blank Output Information Page", at http://inkjetprinterhelp.us/duraink.html , just to first eliminate that very common failure problem. Get More Info To keep those prices so low, quality is sacrificed and options are given up.
my 5400 will not print magenta or yellow. The longer the clog has been in, the worse it is to remove. appropriate to those of us who have suffered a beating by Epson, don't you think? Denny Conway by Denny Conway on Apr 21, 2005 at 2:22pm Add comment Please sign in to comment I have a CX 6600 epson.
The image size settings in your software determine the size of the printed image. IF YOU DECIDE TO, TRY THE "EPSON STYLUS HEAD CLEANING SOLUTION", JUST REMEMBER: The nozzles inside the print head assembly can be easily damaged by using to much force on the Press the left Menu button on the control panel until you see Nozzle Check. See Advanced Scanning With EPSON Scan for instructions.
The lamp turns off automatically to save power (sleep mode); it comes on when you start scanning. The most difficult part was reconnecting the tiny hose onto the plastic nipple under the cleaning pad (in the end my girlfriend with her small fingers and two pair of thin If you're printing over a network, see Setting Up Network Printing. I've only used Epson cartridges.
Replace the cartridge as described on page 8. Press the On button to turn off the EPSON Stylus CX5400, then press the button again to turn it back on. by moe on Jun 7, 2005 at 4:03pm Add comment Please sign in to comment 0 I bought 3rd party ink for the printer and the black and cyan work but I am not a repairer by trade though, but it has been successful for me.
Close other programs, including screen savers and virus protectors, and install again. PS I never did get the tubes back together. This is the same chemical used by epson in their service department. I've already run several head cleanings, a couple head alignments and tried reseating the ink cartridges and "recharging them" again.
Low and behold that was the problem.