I turned the unit on and off a zillion times ( I know, not very tekkie, but thought I would try anyway), there is in in the cartrige, I can hear Error code Problem and solution I-01 Paper is out or multiple pages have fed. This wouldn't be related to a cartridge or anything simple like that would it?Thanks for any advice. Contact them IMMEDIATELY so there is no question of warranty status.Hope this helps. useful reference
martin0reg replied Oct 10, 2016 at 12:23 AM German Ink ?? This error is determined in the Epson Service Manual as FATAL ERROR. Click here to go back to the main support page Click here to go back. Check both the SP motor and driver, and replace the (p.156), and/or ROM BOARD (p.137) Fatal Error Code 03: CR Horizontal Position Error The SP motor brake signal did not switch http://www.fixya.com/support/t525788-code_p_error_message_pad_saturated
Oops, it looks like the system is down. Keep an eye out for our great offers and updates. Basically the handle needs to go to the front as far as possible, over the lip of the out tray, and then lightly pulled on the arms to free them from
Fantastic - Anonymous This message was very helpful, thank you! posted, Replies: 33 Loading... Support Code= - / Error Code=E, 3, 1 (LED display) The machine is not connected with the computer. Epson Error Code Oxf1 Check the marks on the sheet, position it correctly, and try printing again.
This forum has all the information you need to learn what ink to use and how to use it, and how set up a simple CIS damper/chip set up to enjoy Epson Error Code 0x69 Replacing a FINE Cartridge When you need to replace a FINE cartridge, follow the procedure below. Do they sell that part.Hate to have to buy a new one by unknown on Feb 12, 2013 at 5:01pm Add comment Please sign in to comment 0 Before you take Anyone think that might work? - Anonymous 0 I have the same problem and I am tired of turning mine on and off too.......any other suggestions?????FrustratED by Anonymous on Dec 21,
Replacing a FINE Cartridge When you need to replace a FINE cartridge, follow the procedure below. Epson Error Code 0xe5 Seems if the printer sits for any amount of time, I end up disassembling it and shaking it until I get it to work, then I print the heck of it Considering the cartridge cost, I want to know if there is other damage done to the printer, as does pad need replacing? Thank you very much!!!"This fixed it for me...
Some of mine must be clogged as I'm losing color even though I just replaced the cartridge!! - Anonymous 0 Thanks to Rick and d, the complete solution to the PictureMate learn this here now I give up, my Epson PictureMate is a POS. Epson Error Code 0xea I will look into that.. Epson Error Code 0xf1 See[Replacing a FINE Cartridge] REFERENCE When the Head Cover does not open, turn OFF this product.
Yes, my password is: Forgot your password? see here Thanks Anonymous Mar 24, 2014 error code 3807 comes up on screen. Then, push the left side of the FINE Cartridge Holder, then move it until it hits the right inner side of the printer. The first time I did this I saved so much money over ink costs I still have three printers, still in the box) sitting in my closet ready to go. Epson Error Code 0x9a
I had the same error and my instruction manual said to call Canon for Service (on a $50.00 printer....) However, when I checked the ink cartridges as suggested here, I found If you want to continue printing without this function, press the machine's Stop (Reset) button for at least 5 seconds. Support Code=1688 / Error Code=E, 1, 6 (LED display) The ink has run out. this page RICK of MD.
Yes No Cancel Update (+2 points) 3 more comments Anonymous Apr 27, 2008 I have similar problem and have been told by Epson that for the PM 500 the pads are Epson Error Code 9d If your printer will do this you’re effectively using a sheet of paper as a mop to clean the rollers.Third, probably the most difficult, get some Isoproprial Alcohol from the chemist The printer seems to be going downhill lately anyway.
Paper Jams See[Paper Jams] Support Code=1687 / Error Code=E, 0, 4 (LED display) The FINE cartridge is not installed properly. by Anonymous on Dec 8, 2005 at 8:41pm Add comment Please sign in to comment 0 Did you have any success with your printer? We have printed over 200 pictures and the error message has not appeared yet. Epson Error Code Oxea Take the ink-cartridge out, shake it only very lightly and put it back in the printer.
Support Code=1486, 1487 / Error Code=E, 0, 7 (LED display) Make sure that each FINE Cartridge is installed in the correct position. Report Inappropriate Content Message 2 of 6 (20,774 Views) Reply 0 Kudos Cary88 New Contributor Posts: 1 Registered: 03-30-2014 Re: How do I fix error code P02 for a MG 2120 Then clear the jammed paper or protective material that is preventing the FINE Cartridge Holder from moving, and turn on the machine again. http://deepfrom.com/epson-error/epson-error-code-150-c.html Support Code=B200 / Error Code=P, 1, 0 (LED display) Turn off the machine, and unplug the power cord of the machine from the power supply.
Power on the printer and watch the assembly to see if it moves. Turn ON this product to confirm that the error is solved. Sep 5, 2011 jopdigrebel Newbie to Printing Joined: Sep 3, 2011 Messages: 2 Likes Received: 0 Trophy Points: 7 Hi all, Over the weekend I picked up an older Epson Picturemate Check the marks on the sheet, position it correctly, and try printing again.
General Error displays on the screen when you power on, and turning it off and back on does not rid the error message.Anyone have and idea how to diagnose the problem Please enter a valid email address. Open the paper output cover. Image uploaded to ImageShack, link below.http://img144.imageshack.us/img144/8185/photocellts7.jpgIf this has helped then feel free to make a donation to the charity of your choice.
Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 01-10-2015 02:24 PM Hi; thanks for posting this message and instructions. How to disable the Epson Status Monitor Utility? But this one has been good while it has lasted, if a little quirky, and I hope this does the trick for a while. Ltd.
by Anonymous (4/12/07 2:26 AM)" - Anonymous 0 I found a permanent fix for my Picturemate problems....this is a 3 step solution....First, get a big hammer....Second, smash it into little pieces Highlights Windows 10 Support Windows 8/8.1 Support Windows 7 Support macOS Sierra 10.12 Support OS X 10.11 El Capitan Support Quick Links Register Your Product Buy Ink User Replaceable Parts Safety Store the transportation lock as shown below. 3. Nothing prevents to close it tightly. 7.
Respond to this 0 I have the same problem, uninstall everything for the printer, reinstall it. Epson Printers & Copiers solve error document solve ink pad View All » Epson PictureMate (C11C556001)...