The most common OBD-II codes are P0xxx powertrain codes, which are listed below on this page, along with P2xxx generic & P3xxx generic codes (please scroll down). Trans 2059 1) Switch inputs indicate shuttle lever is in both forward and neutral 2) Switch inputs indicate shuttle lever is in both reverse and neutral3) Switch inputs indicate shuttle lever Use kit alone for two-man brake bleeding or with Hand Vacuum Pump (CP7830) for one man brake bleeding.A true DIY brake bleed kitComes with most common... Check specific manufacturer pages on the site, as some of them, we list the OBD2 codes on those pages for those specific vehicles. [ P0000-0100 ] [ P0100-0200 ] [ P0200-0300 http://deepfrom.com/engine-error/engine-error-a-source-engine-is-required-to-run-mods.html
TMF 163 PTO Shaft rotation is detected when the PTO clutch is OFF. Trans 2356 C5-6 clutch Solenoid is shorted to +12 Volts, current sensed while driver isoff. John Bater Jr. It is free and, using an ELM327 or ELM323 interface, can be used to read the fault codes.
ENG 211 Communications problem with Armrest, Instrumentation, or Transmission Controllers ENG 212 Oil Temperature Sensor Voltage is too high ENG 213 Oil Temperature Sensor Voltage is too low ENG 214 Oil TMF 45 Hitch calibration attempted when the engine is not running or engine speed signal is failed. P: Powertrain, (i.e. TMF 81 MFD Solenoid is failed Open or Short Circuit TMF 82 Differential Lock Solenoid is failed Open or Short Circuit TMF 83 Brake Lamp Relay Solenoid is failed Open or
TMF 134 Aux 3rd Raise solenoid failed open or short circuit. ENG 496 Engine Speed / Position Sensor #2 supply is too low ENG 524 Error detected on high speed governor droop selection switch ENG 527 Cab pressurization/Ether relay coil circuit shorted Hitch 1025 Up/Down/Down Momentary switch value received from CAN data bus indicates switch failure. Chevrolet Engine Error Codes TMF 41 Draft pin(s) detected but the Armrest controller specified tractor without draft control.
Trans 2037 Bottom of Clutch pedal switch open circuit or bottom of clutch relay is stuck open Trans 2047 Clutch pedal bottom of clutch switch misadjusted. Chevy Engine Error Codes TMF 44 Hitch calibration aborted due to tractor movement. Engine 3028 Oil Pressure Too Low Engine 3029 Oil Pressure Sensor _Short circuit to Battery Engine 3030 Oil Pressure Sensor _Short circuit to Ground Engine 3031 Oil Pressure Sensor -Hardware Error http://www.troublecodes.net/pcodes/ Diagnostic trouble codes (or fault codes) are codes that are stored by the on-board computer diagnostic system.
INST 10031 Controller Memory Error - Loss of Engine Hours information INST 10032 Controller Memory Error - Loss of Vehicle Configuration information INST 10033 Controller Memory Error - Loss of Customer Check Engine Error Codes If this fault is detected there is a bug in the software Trans 2874 The park brakes commanded on and gear is engaged and there is no park brake request from INST 11011 Fuel Level Sensor voltage is too low (open circuit, short to ground) INST 12011 Communications Lost with Armrest Controller INST 12021 Communications Lost with Auxiliary Controller INST 12031 Communications Trans 2354 C1-2 Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off..
TMF 5 Hitch Lower Solenoid Shorted to 12 volts. http://www.autocodes.com/ Trans 2359 High Clutch Solenoid is shorted to +12 Volts, current sensed while driver is off. Engine Error Codes Ford on 29 January 2013 07:25 PM What is a Diagnostic Trouble Code (DTC)? Jeep Engine Error Codes For the other OBD-II codes, choose from Bxxxx - B Codes - OBD-II Body Codes or Cxxxx - C Codes - Chassis Codes, and Uxxxx - U - Network Codes.
Hitch 1015 Five-volt reference is below the lower voltage limit. this page Trans 2820 System pressure low possible System pressure hydraulic pump failure or leak Trans 2821 System Pressure Low fault Trans 2850 The Park Brake is stuck on by no electrical power TIP: To quickly find an error code, use your browsers Search function. ENG 298 OEM Pressure Sensor Voltage is too low. Engine Error Codes Toyota
Hitch 1026 Up/Down remote fender switch failure. TMF 95 The steering angle sensor is above the expected operating range TMF 96 The steering angle sensor is below the expected operating range TMF 98 Battery Voltage is too Low TMF 129 Aux 2nd Raise Coil solenoid shorted to 12 volts. get redirected here Engine 3003 Foot Throttle Sensor -Signal Below Range Min.
The system returned: (22) Invalid argument The remote host or network may be down. Honda Engine Error Codes Foreign vehicles may also use DTC codes different from the generic DTC codes. ENG 235 Engine Coolant Level is low.
For example, if a DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. If this fault is detected there is a bug in the software Trans 2900 Torque sensor Gap is on the larger end of the tolerance (CCH Only) Trans 2901 Signal received Trans 2024 none of the Transmission clutches are calibrated. Chrysler Engine Error Codes ENG 433 Boost Pressure level disagrees with engine operation conditions (speed & power) ENG 434 Unswitched 12 volt supply voltage disconnected without normal key off sequence.
ENG 2311 Electronic Fuel Injection Control Valve open or closed Circuit. Loosen the drain plug with a wrench. 2. Don't hesitate to download it. useful reference The Vacuum Pump alone can test vacuum operated sensors and components, while the Brake Bleed Kit allows one person to bleed brake fluid easily and cleanly.
The fault is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself. TMF 57 Right Draft Pin voltage is not within spec for Ã¯no loadÃ condition during calibration TMF 58 Left Draft Pin voltage is not within spec for Ã¯no loadÃ condition during TMF 128 Aux 2nd Lower solenoid failed open or short circuit.