Dual-layer break points are committed only when the DVD is formatted onto a dual-layer disc. I feel like I've read every forum, watched every video and no solutions are availing themselves. Meer weergeven Laden... For a single layer disc, all you need to do is burn your material to the disc and the replicator will make a copy of it.However, as you might suspect, dual-layer this contact form
Here's the real frustration: if I capitulate on the burn speed issue, and use DVD Studio Pro to burn the disc, the formatting process proceeds without error. I don't know if the burner in my 2yr old MacBook is broken and won't burn DL disks (the specs say it should), even after I tested burning a single layer Plus, check with the replicator if they want DDP or CMF.Larry replies: Uli, thanks for the additional information. Figure 8 You can then use the Finder's Burn feature to archive up to 8.5 gigabytes of data onto the disc.
On DVD-ROMs, jumping from one layer to the other is a non-issue; but with DVDs a layer change can cause problems with playback. To start viewing messages, select the forum that you want to visit from the selection below. You will need to place a marker around the area you would like to have the break point (Figure 3 below) based on the following criteria: The break point must be We've now reached the point where the Automatic setting is not so automatic.
Transcript Het interactieve transcript kan niet worden geladen. Start to look for a convenient layer- break (LB) point forward from there and set the marker. I used Toast's spanning feature and burned the project to three dual-layer DVDs. Build/Formatby Cade Loven on Jan 17, 2012 at 6:04:53 pmIs there a way to create a disc image without formatting then?Return to posts indexReport Post<< PREVIOUS • VIEW ALL
Other than that, I'm at a loss. Dual-layer media is just that: two layers of the recording dye, each backed by a semitransparent metal reflector and separated by a polycarbonate spacer. Deze functie is momenteel niet beschikbaar. http://www.kenstone.net/fcp_homepage/dual_layer_media_gary.html same problem exists.
keyframegeek 7.122 weergaven 4:45 DVD Studio Pro: Choosing a DVD format | lynda.com - Duur: 5:28. Advertentie Autoplay Wanneer autoplay is ingeschakeld, wordt een aanbevolen video automatisch als volgende afgespeeld. So that led me to the conclusion that there must be some kind of software issue. Logically, I'm thinking to set the layer break at the first chapter of the second video track, but I'm not sure.
James Cawley 3.843 weergaven 10:00 DVD Studio Pro - Building a DVD - Duur: 4:11. The more exotic forms, such as DVD 10s and DVD 18, are two-sided combinations of the basic DVD media. DVD manufacturers of both single- and dual-layer media use a decimal byte system in which 1000 bytes equal a kilobyte. I have been working on this same DVD for about 4 days now.
GetGoing Tutorials 137.393 weergaven 4:11 DVD Studio Pro Tutorial: Using stories when authoring DVDs - Duur: 10:00. weblink You can watch my 7 other in-depth tutorials on my YouTube channel. If it can't after trying however many possibilities the device's firmware tells it to, it returns this error.This is an error generated by the device, not the software.The most common reason With a record, the track starts at the outside and spirals in.
DVD media comes in two basic sizes, DVD-5 and DVD-9, and two basic forms-DVD-R and DVD+R. DL disk burn in DVDSP - just not happening after trying it all... If you want to find out who makes your favorite brand and how it stacks up to others, check out digitalFAQ.com. navigate here If your disc has more DVD-ROM data than movie data, set the Break Point pop-up menu in the Inspector to Automatic and DVDSP will place the break point in the DVD-ROM
Reply Quote Re: Problem burning dual layer DVDs 11 years, 1 month ago #7423 admin OFFLINE Co-Producer Official Geek Posts: 1493 Karma: 0 First, make sure you are using DVD+R media, And every time it failed I was leery of whether it was done right. But when I try to burn it using Toast to disk it fails and says: MEDIUM ERROR Sense Code = 0x73, 0x03 When I try to build it in DVDSP I
Other items on the disk are simple a small slideshow, and some simple menus. I used 2 different Memorex DL DVD on both attempts.Any advise to solve my problem? Figure 9 You can create dual-layer DVDs by either providing raw un-encoded assets or the VIDEO_TS folder if you've already built the DVD. I get the message "Formatting was successful" - then I wasn't clear as to the next process - I just hit burn and gets to about 75% and gives me the
I did a test burn on a 4gig file, single layer and that was fine.... it just doesn't do it well. In most cases I don't need more than one try to get a valid LB.While DLT is still the industry standard for DVD authoring, you can send masters for the two his comment is here I agree DL layer disks are not a great solution, but for this production it's a must.
Dual Layer DVD's are more of a challenge two work with than single-layer discs, but it does offer double the media capacity for your troubles. So it's really a matter of preference of how you want to deliver your product. TrackBack URL for this entry: http://www.geniusdv.com/weblog/mt-tb.cgi/1238 Receive FREE Tutorials by email: HANDS-ON COURSES in ORL Avid Media Composer Training Adobe Premiere CC Video Suite Training (5 days) After FX + Cinema You may see no-name, non-branded media offered at great prices; but if you factor in the "coaster percentage" for inferior media, it most likely will end up costing you more.
Of all the threads on this topic, it appears that no one has found a solution. The laser starts at the center of the disc and lays down data until it either runs out of data or runs out of disc.With a dual-layer disc, things get a My burner is new, so it can't be messing up. For the greatest compatibility, have your disc replicated by a mass production house.
Video is stored in VOB's (Video Object Blocks) which, in turn, are stored in VTS's (Video Title Sets). I get the error message with something about Medium error: sense code 0x0c. I agree, the DL breakpoint can be really tricky. To ensure proper placement, burn to DVD from within DVDSP.